Maintaining an UltraClear Epoxy Table with Ease

Keeping an epoxy-coated table top clean is remarkably easy—especially when it's finished with UltraClear Bar & Table Top Epoxy. The resin's non-porous, ultra-smooth surface not only prevents staining with a waterproof seal, but it's also highly resistant to scratching and water damage, making routine cleaning simple and fast.

In this guide, we outline safe cleaning products, provide recommended maintenance routines, and discuss how UltraClear Epoxy compares to lower-quality alternatives when it comes to long-term upkeep.

What Cleaning Products Are Safe?

Epoxy is highly chemical-resistant, but not all cleaners are ideal for maintaining its clarity and shine. Here's what to use—and what to avoid:

Materials That Are Safe to Use:

• Mild dish soap and warm water

• White vinegar diluted with water (1:1)

• Isopropyl alcohol (70% or less)

• Non-abrasive surface cleaners labeled "resin-safe"

• Microfiber or soft cotton cloths

Materials You Should Avoid:

• Abrasive powders or scouring pads – These can dull the surface over time.

• Ammonia-based cleaners – Prolonged use can degrade the epoxy’s top layer.

• Bleach or harsh solvents – May cause yellowing or cloudiness on inferior resins.

Always test a small area first if you decide to use a cleaning product you're unsure of.

Cleaning Methods: Routine and Deep-Clean

Maintaining your epoxy table top doesn’t require special equipment—just consistency and a gentle touch.

For Daily or Weekly Cleaning:

1. Wipe down the surface with a soft, damp microfiber cloth.

2. Use mild dish soap as needed.

3. Rinse with clean water and dry with a dry cloth to prevent water spots.

For Eliminating Germs:

To sanitize your epoxy table top, especially in kitchens or high-use areas:

1. Mix a solution of 70% isopropyl alcohol and 30% water in a spray bottle.

2. Lightly mist the surface and let it sit for 30–60 seconds.

3. Wipe dry with a clean microfiber cloth.

This method effectively sanitizes the surface without harming the epoxy layer. Avoid repeated daily use of stronger disinfectants to preserve the finish.

Most sanitizing wipes are perfectly fine for use on epoxy.

For Removing Stubborn Messes:

• Sticky residues (e.g., syrup or adhesive): Use isopropyl alcohol on a soft cloth and gently rub the area. Rinse and dry.

• Grease smudges: A diluted vinegar solution can cut through oils without damaging the finish. Avoid using pure vinegar, as its acetic acid can soften your epoxy sheen.

• Water rings or dull spots: Buff lightly with a soft cloth and a dab of resin-safe polish.

Avoid over-scrubbing—even though UltraClear finishes are tough, harsh techniques can reduce surface gloss over time. If your finish does start to dull, you can restore the it to its original shine with a fresh epoxy flood coat. For a quicker fix, consider applying a resin-safe polish instead.

Why UltraClear Epoxy Makes Maintenance Easier

Not all epoxy finishes are equal, and many resins on the market suffer from flaws that make maintaining a clean finish much more difficult. These lower-quality epoxy resins often exhibit:

• Cloudy or soft cures that trap dirt

• Sticky finishes that attract dust

• Low UV resistance, which causes yellowing over time

Unfortunately, there are many budget-brand epoxies, most of which are imported to the U.S. from overseas locations where they can be produced within areas that have lower quality and safety regulations.

Achieve a Perfect Finish with UltraClear Bar & Table Top Epoxy

In contrast to most resins, UltraClear Bar & Table Top Epoxy offers a hardened, crystal-clear surface that doesn’t trap grime and resists scratches better than bargain alternatives. It’s also:

• 100% Made in the USA

• Formulated to resist yellowing and surface wear

• Fully self-leveling for a smooth, non-porous coat

• Beginner friendly with a professional-grade finish

This means less time spent scrubbing and fewer chances of permanent marks or stains—ideal for kitchens, bars, coffee tables, and high-traffic surfaces.

FAQs: Epoxy Table Top Maintenance

Question #1: How do I remove a dried-on spill without damaging the surface?

Soften it with warm water or isopropyl alcohol, then wipe gently with a microfiber cloth.

Question #2: Can I use a disinfectant wipe on my epoxy table top?

Yes, as long as it’s alcohol-based and does not contain bleach or abrasives.

Question #3: Will cleaning too often damage the epoxy?

No—as long as you’re using appropriate materials. Regular gentle cleaning is better than letting grime build up.

Question #4: What if my epoxy finish becomes scratched?

Light surface scratches can often be buffed with a resin-safe polish. For deeper damage, a new flood coat may be needed.

Learn how to repair damage to your finish here.

Question #5: Can I wax an epoxy table top?

It’s not necessary, but using a resin-compatible polish can provide different visual effects (e.g., a diffused sheen) and further enhance epoxy's superb scratch protection.

Question #6: How long does the shine last with regular cleaning?
The high-gloss shine of an UltraClear Epoxy finish will last a minimum of 7 years with proper care.

Additionally, when the right time comes, any epoxy finish can be easily restored with a fresh flood coat of UltraClear Bar & Table Top Epoxy.

Have Questions? Want Advice? We're Here to Help!

If you have any questions about cleaning or maintaining your epoxy surfaces, or if you'd like assistance in planning an epoxy project, please reach out to us at UltraClear Epoxy—our epoxy experts are ready to assist!

You can contact us via phone or email here. During business hours, you can also text chat online with one of our resin specialists by clicking the Help button at the bottom of your screen.

In our online store, you'll find a variety of useful tools and supplies, ideal for resin projects, plus our award-winning UltraClear Bar & Table Top Epoxy and our UltraClear Deep Pour Epoxy.